Clip it into the balloon, fill through it, lock it shut, then breathe through the mouthpiece. Your mouth only touches plastic, and nothing leaks between breaths. The drawing is a true slice through the printed parts; the balloon is drawn small.
SEALED · LOCKED
Two pins on the mouthpiece ride this track cut into the collar. Up the slot is sealed, down is open, and the side notch at the top locks it sealed. Flange marks: one dot = unlocked, two dots = locked.
Step 1 of 4
Press Play to watch all four steps.
Fill from any tank
Small crackers fit straight into the mouthpiece. For bigger nozzles and full-size tanks, snap an adapter onto the tip. Every adapter clips over the bead on the mouthpiece, so pressing down opens the valve and lifting pulls it back to sealed, same as step 3. The adapters are held on by that snap only, on purpose: if a tank pushes too hard, the adapter pops off instead of the balloon or the valve taking it.
Crackers · nozzles 7–11 mm
Straight in
The tip is a gentle taper, so any nozzle 7 to 11 mm across seals on its rim.
No extra parts.
Galaxy-style small tanks · nozzles 6–21 mm
Soft funnel (TPU)
Keep the tank's own nozzle or dispenser on it, as you normally would.
Press the nozzle into the funnel; the soft wall seals on whatever size it is. Also works with tilt-valve nozzles.
Open the dial slowly.
Full-size medical or industrial tanks
Hose barb + regulator
Run the tank through a nitrous regulator set low, about 5–10 psi, then a 1/4″ or 3/8″ ID hose. Print the matching adapter.
Drop the TPU washer into the adapter before snapping it on.
If your big tank has its own balloon-fill nozzle instead, use the funnel.
The parts in 3D
Drag to turn it, scroll or pinch to zoom. Turn on the cutaway to see the O-rings, side ports and gas passage inside.
Print it
Every file is built into this page. Click a column heading to sort.
Part
File
Material
Qty
Print orientation
Size (mm)
Needed for
Download
PETG parts
0.2 mm layers (0.12–0.16 on the mouthpiece for a smoother bore).
4+ walls and 100% infill so the body is gas-tight.
No supports. Avoid PLA: tank gas is cold enough to make it brittle.
The funnel and washer are what seal on nozzles, so print them soft, not in PETG.
Buy, don’t print
2× O-ring, 12 mm ID × 2 mm, silicone.
Food-grade silicone grease for the O-rings.
Leak test before first use: fill with air, lock it, dunk the valve in soapy water. No bubbles means it’s good.
How it seals
The stem has 4 side ports between two O-rings (12×2 mm). Pulled out, the mouthpiece bore covers both rings and traps the ports. Pushed in 8.5 mm, the bore edge drops below the ports and gas flows. Balloon pressure pushes sideways, so it never opens or closes on its own.
Sized for punch balloons
Spigot core 13.0 mm, barbs 15.5 mm, 4 barbs over 25 mm, clip ID 13.2 mm for latex about 0.9 mm thick. If your brand's neck is tighter or looser, measure it and change the preset in balloon_valve.py.
Keep it chill
Never breathe straight from the cracker, tank, nozzle or hose. That gas is freezing and pressurized. Fill the balloon first.
Keep tanks upright so only gas comes out. A tipped tank spits liquid that is far colder, freezes skin and can crack the plastic.
Never open a full-size tank into anything sealed without a regulator. If an adapter pops off, turn the flow down.
Sit down, and breathe regular air between balloons.
One mouthpiece per person, or wash it between people.